Putty Sprayer Machine From Factory in Stock

Putty sprayer machine
Product description:
Mainly used for indoor and outdoor spraying, waterproof grout and waterproof surface coating, waterproof coating, filling, spraying ceilings, walls spray, paint spraying, landscape painting, embossed paint spraying, spraying handicrafts, lacquer, rockery painting, sculpture spray can, sound-absorbing material spraying.

Per hour can be easily sprayed 330m2, work efficiency increased by 25 times.
Basically no ground ash, water, materials, can reduce the cost of 20 or more.
Main parameter:
Suitable for spraying material:

Grout. Insulation mortar, waterproofing materials, fire prevention materials, insulation materials, sound-absorbing materials, putty, paint, white latex, lacquer, water, mud, and other water-soluble material, plastic material.

Features:
First, the simple, before putty, putty stirring mixer can be used to complete, so uniformly viscous putty both moderate,
Much better than manual mixing effect.
Second, spraying fast, if you use a putty sprayer, then spray the wall can only take a few minutes to complete,
If the construction operation, then progress will be much slower.
Third, spray evenly, using a putty sprayer words, because when used in spraying is constant pressure and nozzle
Therefore, the thickness of the coating is better mastered, there will be no uneven phenomenon, which do better than artificial
Fourth, to save material, use putty sprayer, you can control the speed and thickness of the coating sprayer,
Than manual operation to save material.

Practice:
1. Turn the power on, press play button, screw pump began to work. If turned upside down, press the stop button to stop.
Adjust the power at the beginning and inverted, change good turn. As in the opposite direction will not feed.

2. Inject a small amount of imports in the delivery hose water, or water with a screw pump moist delivery hose,the tube was then gradually the memory of water discharged from the outlet. Drainage should be clean, and may not retain the remaining water inside the tube
3. The duct and mortar tubes tied alongside. Exhaust duct connected to the gun.
4. Stir the material into a hopper (which can be opened with the powder used).
5. Press the start button, spraying work begins. At work, adjust the air volume in combination, can achieve optimum coating quality.
6. Variable speed screw pump, the output flow rate of 0-8 l / min, at work,
Just reflux adjusted to suit the construction requirements of the output speed can be.
7. Hopper must be stirred constantly adding good material, in order to ensure the continuity of painting work.
When spraying work be suspended, press the stop button to enable more convenient operation,
The following methods can be used for remote control: the electrical box in the middle knob to the left button is a manual control switch.
8. Before the end of the spraying work to be remaining material hopper after spraying, turn off air pump, after the shutdown.
9. Remove the gun and clean disassembled parts piece by piece.
10. Into the water in the hopper, button power pump water. When the nozzle out of the water was clear,stop button, remove the delivery hose and rolled.

Care and Maintenance:

1. Every pump core cleaning is completed, you must add a little silicone lubricating and anti-embroidered,
Its purpose to protect the transfer of the core will not rust and next time start smoothly.
2. When the machine is working, the electric box door must be closed and locked, to prevent dust and water intrusion, damaging the machine components.
3. Every day before work or after work bearing must refuel and regular checks of gearbox oil.
4. While moving the machine at the construction site, regardless of distance, you must unplug the power cord.
5. When cleaning machine, electrical box section can only be wiped, can not wash.
6. Spindle seal gland alignment, the pump must stay off the core and feed, and then tighten the three screws,
Standard screw tightening after: the 8-inch live hand easily pulled spindle screw prevail.

Troubleshooting:

1. operation, automatically shut down suddenly, possible causes are:
A: Construction site sudden power failure, if the power supply is not restored in a short time, it must cut off the power to remove the delivery hose,
Pump core and all the accessories, and cleaning. When removing pipes, must be covered with a bag or disassembly of the other items,
Prevent open instantly, tube sudden release of pressure, injection mortar danger.
B: motor overload, check the fuse is blown.
2. The slurry is too dry or too long and did not stop cleaning, may lead to blockage malfunction.
Clogging failure is caused by excessive load of one of the reasons, when such a situation occur,
It must clear the blockage site. First turn off the power, and not immediately disassembling the gun or the delivery hose,
Otherwise, due to the enormous pressure pipe will be released from the demolition at the risk of burst shooting mortar
A: The power supply was adjusted to reverse direction.
B: Press the power button, the machine upside down for about 30 seconds, in order to reduce the pressure within the delivery pipe.
C: remove the gun, and cleaning. Check nozzle is blocked.
D: the power switch to forward, to boot.
E: If the delivery hose no material sent, indicating that the inner tube blockage, clean the gun even better, you can continue spraying work.
F: If the delivery hose no material sent, indicating that the inner tube blockage, can be repeated several times to start reversing.
If there is still no material sent out, remove the duct cleaning dredge, remove the delivery hose, it must be carried out in the open reversed.
G: will have to clear the duct connected, and then transferred to the forward button, restart work.
3. Turn the machine moving normally, but a very slow or no pulp slurry may be because:
A: pump core used for too long has been worn, how to judge whether the pump core wear?
Pressure gauge can be connected between the pump outlet and delivery hose core, if the gauge shows little pressure or no pressure,
It can determine the pump core is worn. That is, to get a new pump core.
B: rotating part of the hopper is evacuated, a space, because the paste is too dry or dry stream persuade the poor,
Not suitable for mechanical operation, in this case, because no pump core material will produce dry friction phenomenon,
Soon the pump core high temperature and burned